Skip to content
MeasureToBuy

Tile Layout Patterns: Brick, Diagonal & Herringbone

Compare straight, running bond, diagonal and herringbone tile layouts, the 33% offset rule for large tiles, and how to centre a layout without thin cuts.

Updated November 16, 2026

The short answer

Any pattern works with small tile. The rules start when the tile gets big or the room gets awkward. For tile with a side over 15 in laid in running bond, ANSI A108.02 limits the offset to 33%, unless the tile maker says otherwise. For any pattern, centre and balance the layout so cuts on opposite walls match, and avoid cuts smaller than half a tile.

Pitch = tile + joint
Cut = (room − k × pitch − joint) ÷ 2
Aim for a cut of ½ tile or more

Here k is the number of whole tiles across the room, the pitch is one tile plus one joint, and the cut is the width of the cut tile at each wall. Two cuts around k whole tiles make k + 1 joints: k of them are in the pitch, and the last one is subtracted once.

Tile installations leave a movement gap at the perimeter, and the tile or setting-material maker (and the TCNA Handbook) specifies how wide. The room width above is the width you can tile, so take the gap off each wall first: Cut = (room − 2 × gap − k × pitch − joint) ÷ 2. The worked example below assumes no perimeter gap.

The common patterns

The pattern decides where the cuts fall, and so how much work and waste the room carries.

PatternHow it is laidWhat to plan for
Straight (stacked)Joints line up in both directions, forming a grid.Cut tiles fall along the walls.
Running bond (brick)Each row is shifted along its length against the row above, often by half or a third of the tile.Large tile has an offset limit (next section).
DiagonalSquare tiles turned 45° to the walls.Every wall edge needs angled cuts.
HerringboneRectangular tiles set at right angles to each other in a zigzag.Laid at 45° to the walls, every edge needs angled cuts, and the pattern has to be centred.
BasketweavePairs of rectangular tiles alternate between horizontal and vertical, like woven strips.Plan the layout so the pairs stay whole.

Pattern layouts with angled edges generally leave more offcuts. The waste guide has the allowances we use for each.

The 33% offset rule for large tile

Large tile is rarely perfectly flat. The Ceramic Tile Education Foundation explains that long-edge warpage leaves a high point in the middle of one tile beside the low ends of the tiles next to it, so a half offset puts those high and low points next to each other and shows as lippage (a raised edge).

ANSI A108.02 (section 4.3.8.2, as the Foundation quotes it) therefore caps the offset of running-bond patterns at 33%, unless the tile manufacturer specifies otherwise. It applies when the side being offset is over 15 in nominal. A larger offset needs the owner and the specifier to approve a mock-up and the lippage that goes with it.

TileSide offsetLargest offset within 33%½ offset
12 × 12 in12 inNot limitedNot limited
12 × 24 in24 in7⅞ in12 in
6 × 36 in36 in11⅞ in18 in

The same section sets a wider grout joint for these patterns. For running bond with any side over 15 in, the average minimum joint is ⅛ in for rectified tile and ³⁄₁₆ in for calibrated tile, and it is increased by the edge warpage on the longest edge. Rectified tile with ¹⁄₃₂ in of warpage needs an average joint of ⁵⁄₃₂ in. Check the tile’s own instructions first, since the manufacturer can allow more.

Random plank layouts can land between a third and a half offset. The Foundation advises agreeing the pattern, the offset and the joint width in writing, with a mock-up, before you set tile.

Centre the layout, avoid thin cuts

The same standard sets two layout rules, which the Foundation quotes from section 4.3:

  • Centre and balance areas of tile where possible. That means equal cuts on opposite sides, rather than starting with a full tile at one wall and leaving a thin leftover strip at the other.
  • Usually, no cuts smaller than half a tile, and all cuts on the outer edges of the field, where a baseboard or sealant joint can cover them. Patterns and mosaics can justify many small cuts when they are part of the design.

There are two ways to centre in each direction: on a tile, with a whole tile in the middle, or on a joint, with a joint in the middle. Work out both and take the one that gives edge cuts of half a tile or more.

Worked example: a 136 in wide room

12 in tile with ⅛ in joints, centred across a room 136 in wide (11 ft 4 in):

Pitch = 12 + 0.125 = 12.125 in
Room  = 136 in
Centred onWhole tiles (k)Edge cutOf a tile
A joint107⁵⁄₁₆ in61%
A tile111¼ in10%

The sums: with 10 tiles, (136 − 10 × 12.125 − 0.125) ÷ 2 = 7.3125 in. With 11 tiles, (136 − 11 × 12.125 − 0.125) ÷ 2 = 1.25 in.

Centring on a joint gives 7⁵⁄₁₆ in cuts on both walls. Centring on a tile leaves a sliver only 1¼ in wide, which breaks the half-tile guideline. Do the same sum in the other direction, since the room is rarely the same size both ways.

Dry-lay before you set anything

  1. Find the centre of each wall and snap a line across the room in each direction.
  2. Lay a row of tiles dry along each line, with spacers, out to the walls.
  3. Check the edge cuts at both ends. If one is under half a tile, switch between centring on a tile and on a joint, which shifts the layout by half a tile.
  4. Check the doorway and any other focal point, so the pattern looks planned from where people stand.
  5. For patterned and large-format tile, lay a small mock-up to confirm the offset and joint with whoever is paying for the job.

How the pattern changes what you buy

The pattern changes the number of cuts, and so the offcuts, but not the area you measure. Enter the floor area as usual, then raise the waste allowance for angled and patterned layouts. The Tile Calculator has a waste input for this, and the waste guide explains the allowances. Large tile in a small room also leaves more unusable offcuts, so allow for that too.

Wider joints for large offset tile use more grout, and the trowel size depends on the tile size, so check both. The thinset guide covers the trowel and coverage rules.

In metric

The figures above are in US units, as the manufacturers and standards give them. Here they are in metric, converted with the same factors the calculators use. Switch any calculator to m · cm to work in metric from the start.

Figure in this guideUSMetric
Large tile, side over 15 in15 inches≈ 381 mm
Worked example room width, 136 in136 inches≈ 3,454 mm

Calculate it for your project

Enter the floor and tile size in the Tile Calculator, then add the thinset and grout with your joint width. Tiling a bathroom? The Bathroom Tile Calculator and the bathroom tile planner do the floor and walls together.