Skip to content
MeasureToBuy

Grout Calculator

Enter the tiled area, tile size, joint width and tile thickness. You'll get the pounds of grout, the bags to buy and whether you need sanded or non-sanded grout.

Measurements

Measure the area by

For a wall, enter its height.

⅛ in (3 mm) is common; 1/16 in for rectified tile.

Joint depth — usually the tile's thickness.

Waste allowance

LATICRETE: 10% extra is customary for jobsite waste; more for unglazed quarry tile.

Bag size

Your estimate

You need 1 25 lb bag of non-sanded grout.

2.5 lb of grout for 40 sq ft of 12 in × 12 in tile, plus 10%.

Area
40 sq ft
Joint
0.13 in wide × 0.38 in deep
Grout needed
2.5 lb
Waste allowance
10%
Grout to buy
2.8 lb
25 lb (11.3 kg) bags
1 bag
Grout type
Non-sanded (joints up to ⅛ in)
  • Mosaics and small tiles have far more joint per square foot, so they use several times more grout than large tiles.
  • Manufacturer charts differ by product; this estimate sits close to Custom's Polyblend Plus chart for common sizes.
Tile layout
8 ft5 ftTILE 12 in × 12 in · JOINT 0.125 in
8 tiles across × 5 down in a straight lay. Shaded tiles along the edges are cut pieces.

Next step

Need the thinset too?

Work out bags of mortar for the same area by trowel size.

Thinset calculator

Also useful

Still counting tiles?

The tile calculator works out tiles and boxes for the same surface.

Tile calculator

How to measure

  1. Measure the tiled area: length × width of the floor, or width × height of the wall.
  2. Measure one tile's length and width, and its thickness (the joint depth).
  3. Use the joint width set by your spacers — ⅛ in (3 mm) is common; rectified tile often uses 1/16 in.

How the grout calculation works

Tiles in the area = area ÷ ((tile length + joint) × (tile width + joint))
Grout volume      = tiles × joint × (length + width) × depth
Grout weight      = volume × 1,600 kg/m³ (≈ 100 lb/cu ft) × (1 + waste)

Each tile has one joint along its length and one along its width. Multiply that joint area by the depth to get the grout volume, then by the density of the dry powder to get the weight you buy.

Small tiles have far more joint per square foot, so a mosaic floor can use ten times the grout of a large-format tile floor.

Worked example

A 8 × 5 ft floor in 12 × 12 in tile, ⅜ in thick, with ⅛ in joints and 10% extra.

  1. Area: 40 sq ft = 5,760 sq in; tiles: 5,760 ÷ (12.125 × 12.125) = 39.2
  2. Grout volume: 39.2 × 0.125 × 24 × 0.375 = 44.1 cu in
  3. Weight: 44.1 cu in ≈ 722 cm³ × 1.6 g = 1.16 kg (2.5 lb); with 10% = 2.8 lb

About 2.8 lb of non-sanded grout — one bag is plenty.

How much extra to allow

Grout is mixed in batches and some is always left on the float and in the bucket. Unglazed quarry tile and textured surfaces hold extra on the face.

SituationAllow
Glazed tile, ⅛ in joints10%
Unglazed quarry or textured tile15–20%

Reading your result

The bag row is what to buy. If you're between bags, the smaller bag is usually enough for touch-ups.

Mix only what you can grout in about 20–30 minutes, or follow the bag's working time.

Assumptions

  • Dry grout powder density about 1,600 kg/m³; for 12 × 12 in tile this lands close to Custom's Polyblend Plus coverage chart.
  • Joints are filled to the tile's full thickness.
  • Non-sanded grout for joints up to ⅛ in and sanded for ⅛–½ in, following the Custom Polyblend Plus data sheet. Mapei Keracolor S allows up to ⅝ in.
  • 10% extra is customary for jobsite waste (LATICRETE Grout Guide).

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

Frequently asked questions

How much grout do I need for 100 sq ft?

For 12 × 12 in tile with ⅛ in joints and ⅜ in thickness, about 6.4 lb before waste. Custom's Polyblend Plus chart says a 25 lb bag covers 348 sq ft of that tile.

Sanded or unsanded grout?

Non-sanded for joints up to ⅛ in, sanded for wider joints — Custom Polyblend Plus sanded is rated for ⅛–½ in.

Why do small tiles need so much more grout?

Joint length per square foot grows as tiles shrink. 1 × 1 in mosaics have 24 linear feet of joint per square foot; 12 × 12 in tiles have just 2.

More flooring & tile calculators

All flooring & tile