Skip to content
MeasureToBuy

Project planner

Replace a roof

Turn a building footprint and roof pitch into a complete shingle-roof material list: squares, bundles, starter, ridge cap, underlayment, drip edge and nails, priced with your supplier's numbers.

  1. 01 Building footprint
  2. 02 Roof pitch
  3. 03 Roof area & squares
  4. 04 Waste
  5. 05 Shingles & accessories
  6. 06 Cost
  7. 07 Summary
  1. Step 1: Building footprint

    Measure the walls, then the eave overhang.

    Along the ridge / eaves.

    Eave to eave across the slopes.

    Added to every edge. 0 if you measured at the drip edge.

  2. Step 2: Roof pitch

    Rise per 12 in of run, and the roof's shape.

    Rise in inches per foot of run. Count it with a level and tape, or from the plans.

    Roof style

    Two slopes, triangular ends

    Footprint incl. overhang
    1,344 sq ft
    Pitch
    6/12 · 26.6° · ×1.118
    Roof surface area
    1,503 sq ft
  3. Step 3: Waste

    Hips and valleys mean more cutting.

    Waste allowance

    Cut-offs at hips, valleys and rakes. Hip roofs need more than gables.

    Roofing squares
    15 squares
    With waste
    16.5 squares
  4. Step 4: Shingles & accessories

    Check bundles per square on the shingle wrapper.

    Bundles per square

    Most architectural and 3-tab shingles

    Underlayment

    10 squares per roll

    Shingle bundles
    50 bundles
    Ridge cap bundles42 ft
    2 bundles
    Starter strip bundles
    2 bundles
    Underlayment rolls
    2 rolls
    Drip edge, 10 ft
    17 pieces
    Coil nail boxes
    1 box
  5. Step 5: Cost

    Prices from your supplier.

    per bundle
    per bundle
    per bundle
    per roll
    per 10 ft piece
    per box (7,200)
    Shingles
    $2,000
    Ridge cap
    $130.00
    Starter strip
    $100.00
    Underlayment
    $220.00
    Drip edge
    $170.00
    Nails
    $45.00
    Estimated material cost
    $2,665

MeasureToBuy · project summary

Roof replacement material estimate

Order 50 bundles of shingles plus accessories.

Measurements

  • Building length: 40 ft
  • Building width: 30 ft
  • Eave overhang: 12 in
  • Roof pitch: 6/12
  • Roof style: Gable
  • Bundles per square: 3
  • Underlayment: Synthetic

Key figures

Footprint incl. overhang
1,344 sq ft
Pitch
6/12 · 26.6° · ×1.118
Roof surface area
1,503 sq ft
Roofing squares
15 squares
With waste
16.5 squares

Shopping list

Shingle bundles
50 bundles
Ridge cap bundles42 ft
2 bundles
Starter strip bundles
2 bundles
Underlayment rolls
2 rolls
Drip edge, 10 ft
17 pieces
Coil nail boxes
1 box

Material cost

Shingles
$2,000
Ridge cap
$130.00
Starter strip
$100.00
Underlayment
$220.00
Drip edge
$170.00
Nails
$45.00
Estimated material cost
$2,665

Complex roofs, flashing, vents, decking repairs and disposal aren't included — get a roofer's measurement for anything beyond a simple gable or hip.

Calculators provide planning estimates. Actual material requirements vary with product specifications, installation method, site conditions, local codes and project complexity.

Before you start

  • Measure the building walls and the eave overhang.
  • Find the pitch with a level and a tape measure, or from the house plans.
  • Note anything this won't cover: dormers, skylights, chimneys and valleys need flashing and extra waste.

Questions about this project

Can I put new shingles over old ones?

Many codes allow one overlay, but tear-off is usually recommended so the decking can be inspected. Check local rules and your shingle warranty.

How accurate is a footprint-based estimate?

Very good for simple gable and hip roofs with one pitch. For complex roofs, use a roofer's measurement or an aerial report.

Calculators used in this project

Need just one number? Each step is also a stand-alone calculator.