How to measure
- Measure the finished paved area. Split L-shapes into rectangles and add each one; measure round patios across the middle.
- Pick the paver's nominal size from the label (for example 4 × 8 in). Nominal sizes already allow for the joint.
- Choose the base depth: the Interlocking Concrete Pavement Institute (ICPI) gives 4–6 in for walks and patios and 6–8 in for driveways, more on clay or in frost areas.
- Under Advanced options, enter the sides that butt a house or slab — they don't need edge restraint.
How the paver calculation works
Pavers = area ÷ paver face area × (1 + waste) Base gravel = area × base depth × 1.15, at 1.55 tons per cu yd Bedding sand = area × 1 in Joint sand bags = area ÷ coverage per bag Dig depth = base + bedding + paver thickness
Pavers are counted from face area: a 4 × 8 in paver is 32 sq in, so 4.5 pavers cover a square foot. The waste allowance covers cuts at the edges and broken units.
The base is crusher run (crushed stone with fines) compacted in layers, ordered 15% over its compacted volume. Bedding sand is screeded to 1 in on top. Polymeric sand coverage comes from the bag: Alliance Gator lists 65–85 sq ft per 50 lb bag for ⅛–⅜ in joints and 22–42 sq ft for ¾–1¼ in joints.
Worked example
A 12 × 12 ft patio in 4 × 8 in pavers, herringbone (10% waste), on a 4 in base.
- Area: 12 × 12 = 144 sq ft
- Pavers: 144 × 144 ÷ 32 = 648; × 1.10 = 712.8 → 713 pavers
- Base: 144 × 4 ÷ 12 = 48 cu ft × 1.15 = 55.2 cu ft (2.04 cu yd) × 1.55 = 3.17 tons
- Bedding sand: 144 × 1 ÷ 12 = 12 cu ft ≈ 1,200 lb → 24 bags of 50 lb
- Joint sand: 144 ÷ 65 = 2.2 → 3 bags; edge restraint 48 ft; dig 4 + 1 + 2⅜ = 7⅜ in
Buy 713 pavers, about 3.17 tons of base gravel, 24 bags of sand, 3 bags of polymeric sand and 48 ft of edging, and dig about 7⅜ in deep.
How much extra to allow
Straight running-bond patios with square edges cut the fewest pavers. Herringbone and 45° layouts cut every edge piece, and curves add more.
| Situation | Allow |
|---|---|
| Running bond, straight edges | 5% |
| Herringbone or basket weave | 10% |
| Curves, circles, 45° patterns | 15% |
Reading your result
The highlighted rows are the shopping list. Order base gravel in bulk; bags rarely make sense above a cubic yard.
Dig to the excavation depth, then compact the soil before adding base in layers.
Keep a few spare pavers from the same batch for repairs.
Assumptions
- Base depths follow ICPI Tech Spec 10 minimums (4 in patios and walks, 6 in driveways). Weak or wet soils and cold climates need more.
- Crusher run weighs about 1.55 tons per cubic yard and dry sand about 100 lb per cubic foot; supplier figures vary ±10%.
- Paver thickness defaults to 2⅜ in (60 mm), which ICPI recommends for pedestrian areas and residential driveways.
- Waste percentages are rules of thumb; ICPI does not publish a waste figure.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Driveways on clay, sites with drainage problems, or pavers over a structure (deck, roof) need a design from a hardscape contractor or engineer.
Frequently asked questions
How many pavers are in a square foot?
Divide 144 by the paver's face area in square inches: 4.5 for 4 × 8 in, about 2.67 for 6 × 9 in, 1 for 12 × 12 in and 0.56 for 16 × 16 in.
How deep should a paver base be?
ICPI's minimum is 4–6 in of compacted aggregate for walks and patios and 6–8 in for driveways. Use the deeper end on clay, poorly drained ground or where the ground freezes.
How much sand goes under pavers?
A 1 in screeded bed of coarse concrete sand. About 12 cu ft (roughly 1,200 lb) per 144 sq ft.
How many bags of polymeric sand do I need?
Check your bag's chart. Alliance Gator, for example, lists 65–85 sq ft per 50 lb bag on 2⅜ in pavers with ⅛–⅜ in joints, and only 22–42 sq ft with ¾–1¼ in joints.