How to measure
- Measure the wall's length along the face, following any curves with a tape or string.
- Measure the visible height you want above the finished ground at the front. The buried part is added for you.
- Read the block's face height and length from the label — the face, not the depth into the wall.
- If you're capping the wall, check the cap length; it's often different from the block.
How the retaining wall calculation works
Buried depth = 1 in per ft of wall height Courses = (visible height + buried depth) ÷ block height, rounded up Blocks = ceil(length ÷ block length) × courses × (1 + waste) Base stone = length × trench width × 6 in × 1.15 Drainage stone = length × wall height × 12 in
Allan Block's installation guide buries 1 in of block for each foot of wall height, sets the wall on at least 6 in of compacted wall rock in a trench 24 in wide (18 in for walls under 4 ft), and fills 12 in behind the block with the same clean crushed stone.
Blocks per course and courses both round up, so a 30 ft wall of 11¾ in blocks needs 31 per course even though 30.6 would fit on paper.
Worked example
A 30 ft garden wall, 2 ft visible, in 4 × 11¾ in blocks with 12 in caps and 5% waste.
- Total height: 24 × 12 ÷ 11 = 26.2 in, of which 2.2 in is buried
- Courses: 26.2 ÷ 4 = 6.5 → 7; blocks per course: 360 ÷ 11.75 = 30.6 → 31
- Blocks: 31 × 7 = 217 × 1.05 = 227.9 → 228; caps: 30 × 1.05 = 31.5 → 32
- Base: 30 × 1.5 × 0.5 = 22.5 cu ft × 1.15 = 25.9 cu ft (0.96 cu yd) × 1.4 = 1.34 tons
- Drainage: 30 × 2.33 × 1 = 70 cu ft (2.59 cu yd) × 1.4 = 3.63 tons
Buy 228 wall blocks, 32 caps, about 1.34 tons of base stone and 3.63 tons of drainage stone.
How much extra to allow
Straight walls cut few blocks; corners, steps in the base and curves cut more.
| Situation | Allow |
|---|---|
| Straight wall | 0–5% |
| Corners or a few curves | 5–10% |
| Many curves or steps | 10%+ |
Reading your result
Blocks and stone are the shopping list. A drain pipe is included automatically for walls over 4 ft; add one on any wall where water collects behind it.
The built height can be a little taller than you asked for, because courses come in whole blocks.
Assumptions
- Trench, base and drainage dimensions follow Allan Block's basic installation guide; other systems are similar but check your block maker's instructions.
- Clean ¾ in crushed stone weighs about 1.4 tons per cubic yard; the compacted base is ordered 15% over its volume.
- Hollow block cores also take stone; that volume isn't included.
- Waste is a rule of thumb for broken and cut blocks.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Allan Block's own gravity-wall reference heights fall from about 3–5 ft to under 1½ ft once there's a slope, driveway or building above the wall. Get engineering for any wall over about 3 ft or with load above it.
- The IRC exempts only walls up to 4 ft, measured from the bottom of the footing, that hold back no surcharge; many towns amend this. Taller walls usually need a permit, geogrid reinforcement and a designed drainage system.
Frequently asked questions
How much of a retaining wall goes underground?
Allan Block buries 1 in for each foot of wall height, on top of a 6 in compacted base. Many manufacturers simply say to bury the first course; follow the instructions for your block.
How much gravel goes behind a retaining wall?
A 12 in wide zone of clean crushed stone behind the block, full height. For a 30 ft wall 2⅓ ft tall that's about 70 cu ft, or 2.6 cubic yards.
How tall can a retaining wall be without reinforcement?
It depends on the block, the setback, the soil and what's above the wall. Allan Block's reference table for level ground ranges from about 3 to 5 ft by soil type and drops sharply with a slope or load. Ask your block manufacturer or an engineer.
Do I need a drain pipe?
Allan Block requires one for any reinforced wall, gravity walls over 4 ft, or sites with poor drainage, vented to daylight every 50 ft.