How to measure
- Measure each wall section above the counter end to end — main wall, side wall, island back — and add each as its own section.
- Measure the height from the countertop to the underside of the upper cabinets. 18 in is standard; full-height areas behind a range are often taller.
- Work out the area of anything you won't tile: a window (width × height) or the wall behind a range hood if it stays painted.
- Count outlets and switches in the backsplash area.
How the backsplash tile calculation works
Area = Σ run lengths × height − area left untiled Tiles = area ÷ ((tile w + joint) × (tile h + joint)) × (1 + waste %), rounded up Sheets = area ÷ sheet area × (1 + waste %), rounded up Boxes = tiles (or sheets) ÷ per box, rounded up
A backsplash is a long, narrow strip of wall, so every section shares one height. Windows and painted areas are subtracted before counting tile.
Individual tiles include one grout joint each way in their footprint. Mosaic sheets are made to butt at the same joint as the pieces inside them, so a 12 × 12 in sheet covers one square foot.
Backsplashes have a lot of short cuts at cabinet ends, outlets and windows, so 10% waste is a minimum.
Worked example
A 10 ft counter with an 18 in backsplash in 3 × 6 in subway tile, 1/16 in joints, 40 tiles per box, 10% waste.
- Area: 10 × 1.5 = 15 sq ft
- Tile with joint: 3.0625 × 6.0625 = 18.57 sq in = 0.129 sq ft
- Tiles: 15 ÷ 0.129 = 116.3 → 117 tiles
- With 10% waste: 116.3 × 1.1 = 128.0 → 128 tiles
- Boxes: 128 ÷ 40 = 3.2 → 4 boxes
Buy 4 boxes (160 tiles). As 12 × 12 in mosaic sheets the same wall takes 17 sheets.
How much extra to allow
Small surfaces and many interruptions make backsplash waste higher than a floor, even with a straight layout.
| Situation | Allow |
|---|---|
| Straight or running bond, few outlets | 10% |
| Many outlets, windows or short sections | 15% |
| Herringbone or chevron | 20% |
| Mosaic sheets | 10% — sheets cut cleanly along the mesh |
Reading your result
The headline is tiles (or sheets) with the box count. Buy by boxes unless your store sells single pieces.
Outlet box extenders bring each outlet flush with the new tile face. You'll need one per outlet or switch.
A 10 lb bag of grout, or a small premixed tub, covers most backsplashes.
Assumptions
- Every section is the same height. If one part runs taller (behind a range), add it as a separate section and adjust its length to give the right area.
- Grout for mosaics assumes 1/16 in joints between the pieces at the piece size you enter.
- Edge trim (bullnose, pencil or metal) isn't counted. Measure exposed ends separately.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Moving or adding outlets in the backsplash is electrical work — use a licensed electrician if you're not sure.
- Natural stone and glass mosaics need specific thinset and sealing. Follow the manufacturer's instructions.
Frequently asked questions
How many subway tiles do I need per square foot?
About 7.8 tiles per sq ft for 3 × 6 in subway with 1/16 in joints, before waste.
How high is a standard backsplash?
18 in from the countertop to the upper cabinets. Some homes have 15–20 in; measure yours.
Do I tile behind the stove?
Usually yes, often up to the range hood. If you're leaving it painted or using a stainless panel, enter it as untiled area.
How many mosaic sheets do I need?
A 12 × 12 in sheet covers 1 sq ft, so a 15 sq ft backsplash needs 15 sheets, or 17 with 10% waste.