Skip to content
MeasureToBuy

Gutter Calculator

Enter each gutter run, the roof area draining to it, the roof pitch and your local rainfall intensity. You'll get the gutter length, hangers, downspouts and a check that the gutter size can handle a heavy storm.

Footprint-and-pitch estimates suit simple gable and hip roofs. Roofs with dormers, multiple pitches or many valleys should be measured by a roofer.

Measurements

The plan (footprint) area of the roof slopes that drain here, including overhangs.

in per hour

Example value — replace it with your area's short-duration storm intensity from NOAA Atlas 14 (hdsc.nws.noaa.gov) or your local building department.

Gutter
Downspout

Ground to gutter — the length of each downspout.

Advanced optionscoverage, sizes, custom values

Add outlets for valleys or long runs that dump a lot of water in one spot.

Your estimate

You need 40 feet of 5 in K-style gutter and 1 downspout.

1 run, hangers every 24 in, one downspout per 600 sq ft of roof.

Gutter length
40 ft
Hangers
21 hangers
Downspouts2 × 3 in
1 downspout
Downspout length1 × 10 ft
10 ft

Size check

Roof area × pitch × rainfall
3,960 adjusted sq ft
5 in K-style rated area
5,520 sq ft
Verdict
Large enough
  • Slope gutters about ¼ in per 10 ft toward the downspouts.
  • Runs of 60 ft or more get at least two outlets. Add end caps, outlets, elbows and splash blocks to the list.

Next step

Not sure of the roof area?

Work out the roof's area and pitch from the house footprint.

Roof area calculator

How to measure

  1. Measure each eave where a gutter will hang, end to end.
  2. Work out the plan area of the roof slopes draining to those gutters — length × depth of each slope seen from above, including overhangs.
  3. Pick the roof pitch range, and look up your area's short-duration storm rainfall intensity (inches per hour) on NOAA's Atlas 14 server or from your building department.
  4. Measure the eave height from the ground for downspout length.

How the gutter calculation works

Adjusted area = roof area draining to the run × pitch factor × rainfall (in/hr)
Gutter OK if   adjusted area ≤ rated area (5 in K-style 5,520; 6 in K-style 7,960)
Downspouts    = max(1 per run, 2 for runs ≥ 60 ft; roof area ÷ downspout capacity)
Hangers       = run ÷ spacing + 1

Steeper roofs catch more wind-driven rain, so the roof area is multiplied by a pitch factor (1.0 up to 3/12, 1.05 for 4–5/12, 1.1 for 6–8/12, 1.2 for 9–11/12, 1.3 for 12/12 and steeper). Multiplying by the local rainfall intensity gives an adjusted area to compare with the gutter's rating.

Downspouts carry about 100 sq ft of roof per square inch of opening: a 2 × 3 in downspout handles about 600 sq ft, 3 × 4 in about 1,200 sq ft. Runs of 60 ft or more need at least two outlets.

Worked example

One 40 ft eave draining 600 sq ft of a 6/12 roof, 6 in per hour storms, 5 in K-style gutter, 2 × 3 in downspouts, 10 ft eave.

  1. Adjusted area: 600 × 1.1 × 6 = 3,960 sq ft — under 5,520, so 5 in K-style is large enough
  2. Downspouts: 600 ÷ 600 = 1; the run is under 60 ft, so 1 outlet
  3. Hangers: 40 ft = 480 in ÷ 24 = 20 + 1 = 21

Buy 40 ft of 5 in K-style gutter, 21 hangers and one 10 ft downspout.

Reading your result

If the size check fails, step up to 6 in gutters, add downspouts so each serves less roof, or both.

Slope gutters about ¼ in per 10 ft toward the downspouts.

Assumptions

  • Sizing method, pitch factors and capacities from This Old House; the same method appears in City of Naples and Fine Homebuilding guidance.
  • Each run drains a share of the roof proportional to its length; valleys that dump onto one spot need extra outlets.
  • Hangers every 24 in, or 18 in in heavy snow and ice areas (City of Detroit gutter guide; Amerimax).
  • The default rainfall intensity is only an example — use your local figure.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Gutters on two-storey eaves, steep roofs or with fascia rot are best left to an installer. Seamless gutters are formed on site from coil and can't be bought by the length.

Frequently asked questions

What size gutters do I need?

Multiply the roof area draining to the gutter by the pitch factor and your rainfall intensity. Up to 5,520 adjusted sq ft, a 5 in K-style gutter is enough; up to 7,960, use 6 in K-style.

How many downspouts do I need?

About 1 sq in of downspout opening per 100 sq ft of roof: a 2 × 3 in downspout per 600 sq ft or a 3 × 4 in per 1,200 sq ft, and at least two on any run of 60 ft or more.

How far apart should gutter hangers be?

Every 24 in in most climates and every 18 in where heavy snow and ice load the gutters.

More roofing, siding & gutters calculators

All roofing, siding & gutters