How to measure
- Measure the wall length along the floor where the bottom plate will sit. Frame each straight wall separately, or add lengths only if the walls share spacing and stud length.
- Pick the stud length. Precut 92⅝ in studs with one bottom and two top plates give a wall about 8 ft 1⅛ in tall — right for 8 ft drywall. 104⅝ in precuts do the same for 9 ft.
- Count the doors and windows in the wall and estimate their average rough-opening width for the header length.
- Count corners and places where another wall tees into this one. Each needs extra studs for backing.
How the lumber calculation works
Studs on layout = ceil(wall length ÷ spacing) + 1 Opening studs = openings × 4 (2 king + 2 jack) Corner studs = corners × 2 Studs to buy = (layout + opening + corner) × (1 + waste), rounded up Plate boards = 3 rows × ceil(wall length ÷ plate board length) Board feet = nominal thickness × width (in) × length (in) ÷ 144
Studs go every 16 or 24 in from one end, and the far end always gets a stud even if the last bay is short — hence rounding up and adding one.
Each door or window adds a king stud on each side running full height and a jack (trimmer) stud on each side carrying the header. The layout studs that land inside the opening get cut down into cripples above and below it, so they aren't subtracted.
Corners and wall intersections need extra studs so there is something to nail drywall to on the inside. Two per corner covers a three-stud corner or a ladder-blocked tee.
Plates are one bottom row and a doubled top row. They're counted as whole boards per row, so the offcut from the last board covers the joints.
Worked example
A 12 ft wall of 2×4 precut studs at 16 in on center, with one window and one corner, 10% waste and 12 ft plate boards.
- Layout studs: 144 in ÷ 16 = 9 → 9 + 1 = 10 studs
- Window: 2 king + 2 jack = 4 studs; corner: 2 studs
- Total: 10 + 4 + 2 = 16 studs × 1.1 = 17.6 → 18 studs
- Plates: 3 rows × 1 board = 3 boards of 12 ft
- Board feet: (18 × 92⅝ in + 3 × 144 in) × 2 × 4 ÷ 144 = 116.6
Buy 18 precut 2×4 studs and three 12 ft 2×4s for plates — about 117 board feet — plus header stock for the window.
How much extra to allow
Lumber waste is mostly boards you reject at the yard or on site: crowned, twisted, split or wany studs. Spare studs also become blocking.
| Situation | Allow |
|---|---|
| Hand-picked, kiln-dried studs | 5% |
| Typical yard delivery | 10% |
| Lots of blocking, odd angles | 15% |
Reading your result
The headline is the stud count to buy, with plate boards beside it. Order them together — the plates are the same size lumber as the studs.
Board feet are useful for comparing quotes; yards usually price studs per piece and longer boards per piece or per linear foot.
Header stock is listed as a length only. Its size depends on the span and what sits above it.
Assumptions
- Single top plate splice joints and a doubled top plate; no sill plate on a foundation (add one row of pressure-treated lumber if you need it).
- Openings use one jack stud per side. Wide openings and heavy headers may need doubled jacks.
- Header size, fire blocking, mid-height blocking and sheathing are not included.
- Board feet use nominal sizes (2 × 4), which is how lumber volume is quoted; the actual wood volume uses 1½ × 3½ in.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Load-bearing walls, walls carrying a floor or roof, and any opening wider than about 4 ft need sized headers — check span tables or ask an engineer, and pull a permit where required.
- Building codes vary on stud spacing, height limits and fire blocking. Check with your local building department.
Frequently asked questions
How many studs do I need for a 10 ft wall?
At 16 in on center, 120 ÷ 16 = 7.5 → 8, plus one = 9 studs before openings and corners. Add 4 per door or window, 2 per corner, then 10% waste.
Why add one stud to the count?
Studs are spaced from one end. A wall divided into 9 bays has 10 studs — one more than the number of spaces.
What is a precut stud?
A stud cut to 92⅝ in (or 104⅝ in). With a 1½ in bottom plate and two 1½ in top plates, the wall comes to 97⅛ in — enough for an 8 ft drywall sheet plus ceiling drywall.
Should I use 16 or 24 inch spacing?
16 in is standard and stiffer for drywall and shelving. 24 in saves lumber and leaves more room for insulation but is mostly used with 2×6 walls; check what your local code allows for bearing walls.