How to measure
- Deck length is the side along the house; deck width is how far the deck sticks out. Measure to the outside of the rim joists.
- Board face width is the visible width: 5½ in for 5/4×6 and 2×6 boards and most composite, 3½ in for ×4 boards.
- Choose a gap — 3/16 in is common for dry wood and composite. Wet pressure-treated boards are often laid tight because they shrink.
- Pick the board length you'll buy. Boards that match the deck length avoid butt joints; otherwise joints must land on a joist.
How the decking calculation works
Rows = ceil(deck width ÷ (board width + gap)) Boards per row = ceil(deck length ÷ board length) Boards to buy = rows × boards per row × (1 + waste), rounded up Joists = ceil(deck length ÷ joist spacing) + 1 Screws = rows × joists × 2
Each row of boards takes up one board width plus one gap. Dividing the deck width by that and rounding up gives the rows; the last row is ripped to fit.
Rows longer than one board need two or more boards with a butt joint over a joist. Stagger joints between rows so they don't line up.
Joists run out from the house at 16 in on center (12 in for composite laid diagonally), with one at each end. Every board is fastened with two screws at each joist it crosses, or one hidden clip per crossing.
Worked example
A 16 × 12 ft deck with 5½ in boards, 3/16 in gaps, 16 ft boards, joists at 16 in and 10% waste.
- Rows: 144 in ÷ (5.5 + 0.1875) = 25.3 → 26 rows
- Boards: 26 rows × 1 board = 26 × 1.1 = 28.6 → 29 boards
- Joists: 192 in ÷ 16 = 12 → 13 joists, each 12 ft
- Screws: 26 × 13 × 2 = 676 → 2 boxes of 350
Buy 29 deck boards 16 ft long and 2 boxes of deck screws. The rule of thumb — 350 screws per 100 sq ft — gives 672, which agrees.
How much extra to allow
Deck waste is mostly end trim, a few split or bowed boards, and offcuts from staggering joints.
| Situation | Allow |
|---|---|
| Boards match the deck length | 5% |
| Typical straight layout | 10% |
| Picture frame, diagonal, curved edges | 15% |
Reading your result
The headline is the number of boards at the length you chose. Try a different board length to see if fewer joints or less waste is cheaper.
Joist count and length are for planning the frame. Joist size depends on span — use a span table.
If you choose hidden clips, buy the screws that come with them and check the manufacturer's joist spacing.
Assumptions
- Boards run parallel to the house over joists perpendicular to it. Diagonal and picture-frame layouts need more waste (15%) and closer joists.
- Screws: two per board per joist, ignoring the extra pair at each butt joint.
- Fascia, stair treads, railings, beams, posts and footings are not included.
Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.
When to call a professional
- Ledger attachment, beam and joist sizing, post bases and footing depth are all regulated, and ledger failures cause most deck collapses. Codes vary — check with your local building department and pull a permit.
- Decks more than about 30 in above grade typically need guards and an inspected design.
Frequently asked questions
How many deck boards do I need for a 12 × 12 deck?
With 5½ in boards and 3/16 in gaps, 144 ÷ 5.6875 = 25.3 → 26 rows of 12 ft boards. Add 10% for 29 boards.
How many screws per deck board?
Two at every joist. A 16 ft board over joists at 16 in crosses 13 joists, so 26 screws.
What spacing for deck joists?
16 in on center for most wood and composite boards laid straight; 12 in for composite on a diagonal or thinner boards. Check the decking manufacturer's requirement.
Should deck boards have a gap?
Yes, for drainage and debris — about 3/16 in for dry wood and composite. Wet pressure-treated boards can go tight and will open up as they dry.