Skip to content
MeasureToBuy

Wallpaper Calculator

Wallpaper is estimated the way installers do it: by counting strips, not square feet. Enter the wall width and height, the pattern repeat and the roll size, and the calculator tells you how many rolls to buy.

Measurements

Add the widths of every wall you'll paper. For a whole room, use its perimeter.

Floor (or top of baseboard) to ceiling.

Roll size

20.5 in × 33 ft

Printed on the label. Use 0 for random-match papers and plains.

Advanced optionscoverage, sizes, custom values

Extra length per strip for trimming at the ceiling and baseboard (about 2 in each end).

Add one if the paper is expensive or hard to re-order.

Your estimate

You need 9 double rolls of wallpaper.

26 strips at 8′ 9″, 3 per roll.

Total wall width
48 ft
Openings (50% of their width)
-4.5 ft
Width to paper
43.5 ft
Strips needed20.5 in wide
26 strips
Strip lengthheight + trim, rounded up to whole 21 in repeats
8′ 9″
Strips per roll33 ft roll
3 strips
Rolls for the strips
9 double rolls
Buy
9 double rolls
Wall area papered (approx.)
348 sq ft
  • Each roll gives 3 full strips; the 6′ 9″ left on each roll is offcut — use it above doors and below windows.
  • Check every roll carries the same batch (run) number. Rolls from different batches can differ slightly in color.
  • Consider one spare roll from the same batch for repairs — re-orders rarely match.

Next step

Prime the walls first

Wallpaper goes on best over a wallcovering primer — it helps the paper slide into place and come off cleanly later.

Calculate primer

How to measure

  1. Measure the width of every wall you'll paper and add them up. For a whole room, that's the perimeter.
  2. Measure wall height from the top of the baseboard (or the floor) to the ceiling, at the tallest point.
  3. Count doors and windows and note their widths — standard is about 3 ft.
  4. Read the roll width, roll length and pattern repeat from the label. Random-match papers and plains have a repeat of 0.

How the wallpaper calculation works

Strip length    = height + trim, rounded up to whole pattern repeats
Strips per roll = roll length ÷ strip length, rounded down
Width to paper  = wall width − 50% of door and window widths
Strips          = width to paper ÷ roll width, rounded up
Rolls           = strips ÷ strips per roll, rounded up

Every strip has to start at the same point in the pattern so it lines up with its neighbor. That means each strip uses a whole number of repeats, even if the wall only needs part of the last one. Add about 4 in for trimming at the ceiling and baseboard first, then round up.

A roll only yields whole strips — the piece left at the end is an offcut. That's why a big repeat can drop a roll from three strips to two and add 50% to the order, and why estimating by square footage under-orders.

Doors and windows are only half-deducted. The strips above a door and above and below a window still need full-width paper, and offcuts rarely cover all of them.

Worked example

A bedroom with 48 ft of wall, 8 ft high, one door and two windows (3 ft wide each), a 21 in pattern repeat and US double rolls (20.5 in × 33 ft).

  1. Strip length: 96 + 4 = 100 in → 5 repeats × 21 = 105 in
  2. Strips per roll: 396 in ÷ 105 = 3.77 → 3 strips
  3. Width to paper: 48 − (3 + 6) × 50% = 43.5 ft = 522 in
  4. Strips: 522 ÷ 20.5 = 25.5 → 26 strips
  5. Rolls: 26 ÷ 3 = 8.67 → 9 double rolls

Buy 9 double rolls, all from the same batch. About 2 ft is left on each roll — use it above the door and under the windows.

How much extra to allow

The strip method already includes the real waste: roll ends and pattern matching. Add a spare roll for expensive or hard-to-reorder papers — later batches rarely match exactly.

SituationAllow
Random match or plain paperNo spare needed
Patterned paper, simple room1 spare roll
Large repeat, many corners or a stairwell1–2 spare rolls

Reading your result

The highlighted number is the rolls to buy. 'Strips per roll' is the key figure — if it's low, a narrower repeat or a longer roll changes the order a lot.

US wallpaper is usually priced per single roll but sold in double rolls. Check which one a price refers to before comparing.

Check the batch (run) number on every roll before you start hanging.

Assumptions

  • US double roll: 20.5 in × 33 ft. Euro roll: 0.53 × 10.05 m. Use 'Other size' for anything else, including wide commercial goods.
  • 4 in trim per strip (2 in at each end), adjustable under Advanced options.
  • Openings deduct half their width; door and window widths default to 3 ft (0.9 m).
  • Straight and drop-match papers are both rounded to whole repeats per strip.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Grasscloth, silk, hand-printed and very expensive papers are usually worth a professional hanger — mistakes are costly.
  • Stairwells and ceilings need scaffolding and experience.
  • Damp walls or crumbling plaster need repair before papering, or the paper will lift.

Frequently asked questions

How many rolls of wallpaper do I need for a 12 × 12 room?

With 8 ft walls, a door and a window, about 9 US double rolls for a paper with a 21 in repeat. Random-match papers can need fewer; large repeats more.

What is a pattern repeat?

The vertical distance before the pattern starts again, printed on the label. Strips must start at the same point in the pattern, so each strip uses a whole number of repeats.

Why not just divide the wall area by the roll area?

Because rolls are cut into full-height strips and the leftover at the end of each roll is waste. Area-based estimates typically come up one or two rolls short.

What's the difference between a single and a double roll?

A US double roll is two single rolls on one tube — about 56 sq ft versus 28 sq ft. Most US papers are priced per single roll but sold as doubles, which also gives longer continuous lengths and less waste.

More painting calculators

All painting