Skip to content
MeasureToBuy

Roofing Squares Explained: Squares, Bundles and Pitch

What a roofing square is, how many bundles you need per square, and how roof pitch turns a footprint into roof area.

Updated October 7, 2026

The short answer

A roofing square is 100 sq ft of roof surface (about 9.3 m²). Most architectural asphalt shingles come three bundles to a square. To get squares from the ground, multiply the building footprint (including overhangs) by the pitch multiplier, then divide by 100:

Roof area = footprint × pitch factor
Squares   = roof area ÷ 100
Bundles   = squares × (1 + waste) × 3, rounded up

A 1,200 sq ft footprint at 6/12 pitch is 1,200 × 1.118 = 1,342 sq ft, or 13.4 squares. The Roofing Calculator does this and lists the accessories too.

Squares and bundles

Roofers price, quote and order in squares because it keeps numbers manageable: a typical house roof is a few dozen squares rather than thousands of square feet. Shingles are packed in bundles light enough to carry up a ladder, and the wrapper states how many bundles make a square.

  • Three-tab and most architectural shingles: 3 bundles per square.
  • Heavier designer or laminated shingles: often 4 or more bundles per square.

Always read the wrapper. If you already know your squares, the Shingle Calculator converts them to bundles for any bundles-per-square figure.

Pitch notation

Pitch is written as rise over run: how many inches the roof climbs for every 12 inches it runs horizontally. A 6/12 roof rises 6 in per foot. Low-slope roofs are around 2/12 to 4/12; a 12/12 roof is a 45° slope.

To measure it, hold a level horizontally against the roof surface or a rafter, mark 12 in along the level, and measure straight up from that mark to the roof. That measurement is the rise. You can also measure at the gable end from inside the attic, against the underside of a rafter.

Pitch multiplier table

A sloped roof is longer than the ground it covers. The pitch factor is the length of the slope for each foot of horizontal run:

Pitch factor = √(1 + (rise ÷ 12)²)
PitchMultiplierAngle
2/121.0149.5°
3/121.03114.0°
4/121.05418.4°
5/121.08322.6°
6/121.11826.6°
7/121.15830.3°
8/121.20233.7°
9/121.25036.9°
10/121.30239.8°
11/121.35742.5°
12/121.41445.0°

Pitch makes a large difference at the steep end. The same 1,000 sq ft footprint is 1,054 sq ft of roof at 4/12 but 1,414 sq ft at 12/12, over a third more shingles. For a roof with one pitch throughout, the multiplier works for both gable and hip shapes. The Roof Area Calculator handles the conversion if you only need the area.

Worked example: 40 × 30 at 6/12

A house with walls measuring 38 × 28 ft and 12 in eaves on every side, at 6/12 pitch, gable roof, 10% waste.

  • Footprint with overhangs: (38 + 2) × (28 + 2) = 40 × 30 = 1,200 sq ft
  • Pitch factor for 6/12: √(1 + 0.5²) = √1.25 = 1.118
  • Roof area: 1,200 × 1.118 = 1,342 sq ft
  • Squares: 1,342 ÷ 100 = 13.4
  • With 10% waste: 13.4 × 1.1 = 14.8 squares
  • Bundles: 14.8 × 3 = 44.3 → 45 bundles

If the same house had a hip roof at the same pitch, the area would be identical, but you’d use about 15% waste: 13.4 × 1.15 × 3 = 46.3, so 47 bundles.

A common error is leaving out the overhangs. Measuring at the walls here gives 38 × 28 = 1,064 sq ft of footprint instead of 1,200, which is about 11% short before any waste is added.

Hips, valleys and waste

Roof waste comes from cuts. Every rake edge, hip and valley is a cut line, and each hip or valley produces cut pieces along its entire length on both sides.

Roof typeWaste
Shed roof5%
Simple gable10%
Hip roof15%
Multiple valleys, dormers20%

Hip roofs also need far more ridge cap, since every hip is capped as well as the ridge. Valleys need their own underlayment or metal, depending on the valley method.

Accessories

Shingles are only part of the order. For the 40 × 30 gable above:

  • Ridge cap: the ridge runs 40 ft. At about 33 ft per bundle, that’s 2 bundles.
  • Starter strip: runs along the eaves and rakes. Eaves are 2 × 40 = 80 ft. Each rake is half the 30 ft width times the pitch factor, 15 × 1.118 = 16.8 ft, and there are four, so 67 ft. Total 147 ft; at about 105 ft per bundle, 2 bundles.
  • Drip edge: the same 147 ft of edges, bought in 10 ft lengths, with some allowance for overlaps.
  • Underlayment, nails, vents, flashing and, in cold climates, ice-and-water shield at the eaves. Check local code for where it’s required.

To price the whole list, use the Roofing Cost Calculator.

When to get a professional measurement

The footprint method assumes one pitch across the whole roof. It gets unreliable when the roof has:

  • Sections at different pitches, such as a porch roof below a steeper main roof
  • Dormers, turrets, crickets or multiple intersecting valleys
  • Additions built at different times with different overhangs

For these, run each section separately, or have a roofer measure it or order an aerial measurement report. Roofs steeper than about 8/12, two-storey eaves and any roof with soft or damaged decking need a professional crew with fall protection, whatever the estimate says.

In metric

The figures above are in US units, as the manufacturers and standards give them. Here they are in metric, converted with the same factors the calculators use. Switch any calculator to m · cm to work in metric from the start.

Figure in this guideUSMetric
One roofing square100 square feet≈ 9.3 m²
Footprint, 1,200 sq ft1,200 square feet≈ 111.5 m²
Roof area, 1,342 sq ft1,342 square feet≈ 124.7 m²
Building length, 40 ft40 feet≈ 12.19 m
Building width, 30 ft30 feet≈ 9.14 m

Calculate it for your project

Enter the footprint, overhang, pitch and roof style in the Roofing Calculator to get squares, bundles and the accessory list in one place.