Skip to content
MeasureToBuy

Concrete Block Calculator

Enter the wall size and how the cores will be filled. You'll get the number of 8 × 8 × 16 in concrete blocks (CMU), mortar mix bags, and the grout or concrete needed for reinforced cells.

Structural sizes — footings, framing, stairs — are governed by local building codes and site conditions. Use this for material planning, and confirm sizes with your building department or an engineer.

Measurements

Measure the wall by

Each course of 8 in block adds 8 in (225 mm metric).

Doors and windows, width × height each. 0 for none.

Block face

8×8×16 nominal; 6, 10 and 12 in widths have the same face

Core fill (grout)

Cells with vertical rebar

Each 16 in block has two cells, 8 in apart. Rebar at 32 in → every 4th cell.

Waste allowance

5% covers breakage; use 10% with many cuts or openings.

Your estimate

You need about 95 blocks (5% waste included).

80 sq ft of wall × 1.13 blocks per sq ft, plus 5% waste.

Wall area
80 sq ft
Net wall area
80 sq ft
Blocks per sq ftwith mortar joints
1.13
Blocks laid
90 blocks
Blocks to buy
95 blocks

Mortar (approximate)

Mortar volume≈ 8.5 cu ft per 100 blocks
7.65 cu ft
80 lb bags of mortar mix≈ 0.67 cu ft per bag
12 bags

Core fill (approximate)

Every 4th cell grouted5.85 cu ft at ≈ 0.26 cu ft per full block
0.22 cu yd
80 lb bags of concrete or grout0.6 cu ft per bag
10 bags
  • Mortar and grout figures are approximate estimating rules. Actual use depends on joint fill, core size and how much falls into the cells.
  • Count corner, half and bond-beam blocks separately if your wall needs them — the total stays about the same.
  • Rebar size and spacing in a block wall are set by your design or local code; grout every cell that holds a bar.
Block wall · elevation
20 ft4 ftRUNNING BOND · 8 × 16 IN MODULE
Blocks = (wall area − openings) ÷ area of one block plus its joint. Courses are drawn for illustration, not to scale.

Next step

Size the footing

A block wall sits on a continuous concrete footing below the frost line.

Concrete Footing Calculator

Also useful

Brick veneer instead?

Count bricks and mortar for the same wall.

Brick Calculator

How to measure

  1. Measure wall length and height. Block walls work in 8 in courses, so a height that's a multiple of 8 in avoids cut blocks.
  2. Subtract doors and windows: width × height of each opening, added together.
  3. Decide which cells get grout. Cells with vertical rebar are always grouted; a fully grouted wall fills every cell.
  4. Cell spacing: each 16 in block has two cells 8 in apart, so rebar at 32 in on center means every 4th cell; at 48 in, every 6th.

How the concrete block calculation works

Blocks per sq ft = 144 ÷ (16 × 8) = 1.125
Blocks to buy    = net wall area × 1.125 × (1 + waste)

Mortar           ≈ 8.5 cu ft per 100 blocks laid
Mortar mix bags  = mortar ÷ 0.67 cu ft per 80 lb bag
Core fill        ≈ 0.26 cu ft per fully grouted block ÷ N

A nominal 8 × 8 × 16 in block is actually 7⅝ × 7⅝ × 15⅝ in. Add a ⅜ in joint and each block covers exactly 16 × 8 in of wall — 128 sq in — so 1.125 blocks per square foot. Metric 440 × 215 mm blocks with 10 mm joints come to 9.88 per m².

Mortar and grout are approximate estimating rules, not exact volumes. Face-shell bedding uses about 8.5 cu ft of mortar per 100 blocks, which is roughly 13 bags of 80 lb mortar mix. A fully grouted 8 in block takes about 0.26 cu ft; grouting every Nth cell takes 1/N of that.

Worked example

A 20 ft × 4 ft garden wall of 8 in block, rebar every 32 in (every 4th cell grouted), 5% waste.

  1. Wall area: 20 × 4 = 80 sq ft
  2. Blocks laid: 80 × 1.125 = 90
  3. With 5% waste: 90 × 1.05 = 94.5 → 95 blocks
  4. Mortar: 90 × 0.085 = 7.65 cu ft ÷ 0.67 = 11.4 → 12 × 80 lb bags
  5. Core fill: 90 × 0.26 ÷ 4 = 5.85 cu ft ÷ 0.6 = 9.75 → 10 × 80 lb bags of concrete

Buy 95 blocks, 12 bags of mortar mix and 10 bags of concrete or grout for the cores.

How much extra to allow

Blocks break in handling and get cut at openings and corners; mortar drops and stiffens on the board.

SituationAllow
Straight wall, few cuts5%
Corners, pilasters and openings10%

Reading your result

The block count is for stretcher blocks. Corner, half and bond-beam blocks substitute one-for-one, so the total stays about the same — just split your order.

Mortar and core-fill bags are rounded up and approximate. Buy a bag or two extra; unopened bags usually return.

Assumptions

  • Standard hollow two-core block with ⅜ in (10 mm) joints and face-shell mortar bedding.
  • 6, 10 and 12 in wide blocks have the same 8 × 16 in face, so the block count is the same; core fill per block scales with width.
  • Grout volume ignores bond beams and grout that leaks into ungrouted cells.

Unit conversions use exact definitions (1 in = 25.4 mm, 1 US gal = 3.785 L). See the calculation methodology for rounding rules.

When to call a professional

  • Retaining walls, foundation walls and load-bearing block need engineered reinforcement, grout and footings. Get plans or a mason before building.

Frequently asked questions

How many concrete blocks per square foot?

1.125 standard 8 × 8 × 16 in blocks per square foot, because each block plus its joint covers 16 × 8 in.

How many bags of mortar per 100 blocks?

About 13 bags of 80 lb mortar mix — roughly 8.5 cu ft of mortar — with face-shell bedding.

How much concrete to fill cinder block cores?

About 0.26 cu ft per fully grouted 8 in block, or roughly 2.3 blocks per 80 lb bag of concrete. Grouting only rebar cells takes a fraction of that.

Is cinder block the same as concrete block?

In everyday use, yes. Modern 'cinder blocks' are concrete masonry units (CMU); true cinder aggregate block is rare today.

More concrete & masonry calculators

All concrete & masonry